Grey Stone Mate Crocodile Tile Adhesive

Special tile adhesive for dark natural stone tile, minimized efflorescence

  • Great for high humidity areas.
  • Minimized efflorescence with CAC technology.
  • Suitable for tiles and dark natural stones of all sizes
  • Suitable for interior and exterior use on floor and wall

USA Standard : ANSI A 118.1, ANSI A 118.4, ANSI A 118.15
Packing
Net Weight : 20 kg/bag
Color : Grey

Store Finder JORAKAY CORPORATION map

Information

Grey Stone Mate Crocodile is powder latex enhanced dry-set mortar, composed of Portland cement, sand and special chemical to avoid efflorescence. Excellent for natural stone and all types of tile both interior and exterior installation.

How to use

Grey Stone Mate Crocodile is powder latex enhanced dry-set mortar, composed of Portland cement, sand and special chemical to avoid efflorescence. Excellent for natural stone and all types of tile both interior and exterior installation.

Installation
Preparation
For new substrate : 
The surface must be dry, flat, level and fully cured. It should be free of all grease, oil, dust, curing compounds, old adhesive residues and any other adulterant. Make sure water absorption of the substrate is at normal level. In case of new render or leveling , the substrate should be fully cured for 7 days or 168 hrs. per 1 cm thickness of adhesive before tiling.
For old substrate : Clean up the surface with high-pressure jet spray to remove dust, adulterant and any de-bonding tiles. Remove the left water before re-tiling.

Proportion of Mixing
Grey Stone Mate Crocodile Tile Adhesive 20 kg (per bag) per 4.6 L of water or 2.8-3.2 parts of Grey Stone Mate Crocodile Tile Adhesive per 1 part of water by volume.

Mixing

  • Mix Tile Adhesive with clean, potable water thoroughly until smooth with a mechanical mixer at a low speed (≤150 rpm).
  • Let mortar slakes for 15 minutes before mixing a second time. Do not add water, latex, or additional powder after slaking period.


Application

  1. Spread mortar with flat side of trowel to key-in substrate, and then apply additional mortar to ensure that it cover 100% at the back of tile.
  2. Apply notched side at 60-degree angle in the same direction throughout installation surface.
  3. Recommend to apply the product all over the back of tile to compensate bending, prevent gap under tile that may cause less compressive strength and easily to crack.
  4. After placing tile on the prepared surface, slide it orthogonally to the notched lines and tap in order to maximize bonding.
  5. Tiles can be adjusted for proper alignment within 30 mins after apply the products. Timing may vary depends on temperature. Recommend not to adjust further after setting. Make sure that the products is covered all over the back of tiles. Suitable thickness of tile adhesive on substrate is 3-10 mm.


Curing and Grouting

  • A minimum cure is obtained in 24-48 hours, depending on ambient temperatures.
  • For better quality, Crocodile Tile Grout should be chosen to suit each type of tiles. Crocodile Tile Grout has many types and color for each joints and places


Suggestion    

  • Grouting after tile installation at least 48 hours to achieve maximum efficiency.
  • Recommend to apply the product all over the back of tile to maximize bonding strength.


Limitations    
Able to use over plywood structure. Cement plywood board must be at least 19 mm thick, firmly installed and not bend.
** Please contact us for application on exceptional materials.

Caution    

  • May be harmful to the eyes, skin, or lungs. Wear suitable protective clothing, gloves, and eye/face protection
  • In case of contact with eyes, rinse immediately with water and seek medical advice.
  • After contact with skin, wash immediately with water
  • Keep out of reach of children
  • Do not eat

Storage    
It should be kept in a dry place and the temperature is not too high to avoid product’s degradation. Age of product is 1 year from the date
of manufacturing

Download